MOTM-101 Noise Generator / Sample & Hold

Exclusive
MOTM-101 Noise Generator / Sample & Hold


Synthesis Technology MOTM-101 Noise Generator/Sample&Hold

The MOTM-101 is an essential part of any synthesizer system. It is a dual-function module, where the Noise Generator is linked to the Sample & Hold section without the use of patchcords. Each section can operate independent of the other.

NOISE GENERATOR

The Noise Generator uses two Zener diodes to create white noise. This white noise contains spectral harmonics from near DC to well above hearing. This type of noise is useful for simulating cymbals, ocean waves, static, and other types of "nature" sounds. It is also useful in generating random signals into the sample & hold, and for aperiodic, high-speed clocking.

The white noise is low-pass filtered at approximately 2500Hz to create pink noise. Pink noise is useful for lower frequency sounds such as thunder. The pink noise is filtered even more to generate random output, which can randomly modulate filters and VCOs.

These three types of noise are found on many synthesizers. However, look closely and you will see the jack labeled Vibrato, and its associated control knob! This is a MOTM exclusive: a high-Q bandpass filter (the panel control controls the Q) that generates sine waves centered around 7Hz of random amplitudes (and slightly varying frequencies as well). On the panel, a switch selects driving the bandpass filter with either white noise or the internal/external clock from the sample & hold section. When the panel switch selects white noise, the vibrato output is a 'wandering' sine wave, perfect for adding realistic vibrato and tremelo. If the switch is in the clock position, each time the clock cycles the output filter rings in a dampened sine wave (the ringing amount set by the panel control).

SAMPLE & HOLD

A Sample & Hold circuit is a sort of voltage memory: each time the clock generator cycles, the signal on the Input jack is captured and stored on a special capacitor. This voltage is buffered and fed to the Output jack. Even with many seconds between samples, the output voltage remains nearly constant (since no circuit is perfect, the output voltage will droop, but at a miniscule rate on the order of 1mv per second). The MOTM-101 contains an internal clock oscillator, whose speed is set by the panel control. A red LED flashes at the clock rate. Plugging another clock source (VCO, LFO, etc) into the External Clock input overrides the internal oscillator.

Again, sample & hold is a part of many synthesizers... but wait! Hmmmm... what's that switch marked Track/Hold? Another MOTM exclusive! In the HOLD position, the circuit acts like a "normal" sample & hold: the output is held steady at the start of each clock cycle. But, in the TRACK position, the output follows (tracks) the input when the clock is low (less than 1.5 volts) and holds the output when the clock is above 1.5 volts. If you are familiar with TTL digital logic, this mode is referred to as a "transparent latch." From a musical standpoint, this can generate more unique sounds than other sample & hold modules.

The Slew control adds portamento or glide to the sample & hold output. It can be adjusted from zero to ten seconds.

Demos:

Two MOTM-101s in a cascade, driving three voices (110+300+440+800) [Robert Rich]

Captain, the hull has been breached! [Scott Juskiw]

Two MOTM-300s which are frequency modulating each other [Mike Marsh]

full kit includes everything you need, with each part individually bagged and labelled. 

the kit includes genuine parts including BI/TT P260 potentiometers, Switchcraft jacks, Mountain Switch paddle-actuated switches et al. 


 

On Demand Info

These kits and assembled modules are offered on demand, click the link to learn more.

 

Kit Parameters
Build DifficultyModerate
Parts Count131
Module Parameters
FormatMOTM
Panel Size2U

Write a review

Please login or register to review
  • from $40.00 TO $369.00
  • Ex Tax: $40.00

Available Options

Options
Price
Available
Quantity
Discount
Full Kit
Out of Stock - $235.00
 
 
panel
In stock / $45.00
Available : 8
 
pcb
In stock / $40.00
Available : 88
 
pcb+panel+bracket
In stock / $95.00
Available : 8
 
synthCube assembled, new
In stock / $369.00
Available : 6
 

Tags: motm-101, noise, generator/sample&hold, synthesis, technology generator/sample&hold generator/sample&hold, diy, kits motm-101master generator/sample&hold generator/sample&hold, and generator/sample&hold generator/sample&hold generator/sample&hold generator/sample&hold, analog, modular, motm101mstr generator/sample&hold generator/sample&hold generator/sample&hold generator/sample&hold generator/sample&hold generator/sample&hold generator/sample&hold generator/sample&hold, original, modules generator/sample&hold generator/sample&hold, synthesizer